摘要The pier-girder rigid region of continuous rigid-frame bridges with V-shaped piers has a complex spatial stress state because of its special structure and complex boundary condition. However, using the beam-column element model for mechanical analysis in design induces large errors. Therefore, this study analyzes the spatial stress and structural optimization of the pier-girder rigid region of a continuous rigid-frame bridge with V-shaped piers. A solid model of the pier-girder rigid region is established by photoelastic stress experiment and numerical analysis. The stress distribution characteristics of the pier-girder rigid region in the longest cantilevered stage and operational stage are revealed in view of tri-directional normal stress and boundary tangential normal stress, and the stress distribution curve of slice boundary at key positions is drawn. Results show that (1) the experimental values are consistent with the finite element analysis values, and the compressive stress is dominant in the main girder structure, which meets the design requirements of fully prestressed concrete structures; (2) the tensile stress concentration appears around the hole of the diaphragm in the bridge transverse direction, whereas the compressive stress concentration appears at the joints between the top/bottom plates of the box girder and the diaphragm in the bridge longitudinal direction; (3) the consolidation zone between the V-shaped bracing and the vertical pier is the most dangerous area of the structure, where the structural measurements of increasing the reinforcement or using steel fiber reinforced concrete are proposed. An optimization measure for increasing the height of the vertical pier is introduced to present the property of a flexible pier and optimize the mechanical characteristics of the bridge. As the height of the pier increases, the stress gradient of each section of the V-shaped bracing decreases, and the distribution of cross-section stress becomes uniform. When the height of the pier is greater than five times of the girder height at the pier top, the stress gradient of each section of the V-shaped pier is less than 0.6. Herein, the force is reasonable with large safety reserve, which can adapt to the longitudinal displacement of the main girder caused by concrete shrinkage, creep, and temperature change in the later stage.
Abstract：The pier-girder rigid region of continuous rigid-frame bridges with V-shaped piers has a complex spatial stress state because of its special structure and complex boundary condition. However, using the beam-column element model for mechanical analysis in design induces large errors. Therefore, this study analyzes the spatial stress and structural optimization of the pier-girder rigid region of a continuous rigid-frame bridge with V-shaped piers. A solid model of the pier-girder rigid region is established by photoelastic stress experiment and numerical analysis. The stress distribution characteristics of the pier-girder rigid region in the longest cantilevered stage and operational stage are revealed in view of tri-directional normal stress and boundary tangential normal stress, and the stress distribution curve of slice boundary at key positions is drawn. Results show that (1) the experimental values are consistent with the finite element analysis values, and the compressive stress is dominant in the main girder structure, which meets the design requirements of fully prestressed concrete structures; (2) the tensile stress concentration appears around the hole of the diaphragm in the bridge transverse direction, whereas the compressive stress concentration appears at the joints between the top/bottom plates of the box girder and the diaphragm in the bridge longitudinal direction; (3) the consolidation zone between the V-shaped bracing and the vertical pier is the most dangerous area of the structure, where the structural measurements of increasing the reinforcement or using steel fiber reinforced concrete are proposed. An optimization measure for increasing the height of the vertical pier is introduced to present the property of a flexible pier and optimize the mechanical characteristics of the bridge. As the height of the pier increases, the stress gradient of each section of the V-shaped bracing decreases, and the distribution of cross-section stress becomes uniform. When the height of the pier is greater than five times of the girder height at the pier top, the stress gradient of each section of the V-shaped pier is less than 0.6. Herein, the force is reasonable with large safety reserve, which can adapt to the longitudinal displacement of the main girder caused by concrete shrinkage, creep, and temperature change in the later stage.
基金资助:Supported by the National Natural Science Foundation of China (No.51578161);Research Project for Young and Middle-aged Teachers of Fujian Provincial Department of Education (No.JAT170614)
通讯作者:
ZHANG Fei
E-mail: 597586597@qq.com
引用本文:
张飞, 王燕. Spatial Stress of the Pier-girder Rigid Region of a Continuous Rigid-Frame Bridge with V-shaped Piers in Two Directions[J]. Journal of Highway and Transportation Research and Development, 2020, 14(1): 45-54.
ZHANG Fei, WANG Yan. Spatial Stress of the Pier-girder Rigid Region of a Continuous Rigid-Frame Bridge with V-shaped Piers in Two Directions. Journal of Highway and Transportation Research and Development, 2020, 14(1): 45-54.
[1] SHAO X D. Bridge Engineering[M]. Beijing:China Communications Press, 2016. (in Chinese)
[2] LUO X Y, CHEN A R, LIU B. Aesthetic and Structural Design of Third Panama Canal Bridge[J]. World Bridges, 2017, 45(4):11-14. (in Chinese)
[3] ZHAO S B, LIU S M, YANG Z L, et al. Study on Design of Shape and Structural Project of Continuous Rigid-Framed Bridge with V-Shaped Piers[J]. Journal of Henan University:Natural Science Edition, 2010, 40(1):101-104. (in Chinese)
[4] YU L S, ZHU D S. Local Stress Analysis of Rigid Fixity Joint of Pylon, Girder and Pier of an Extradosed Bridge[J]. Bridge Construction, 2008, 38(1):54-57. (in Chinese)
[5] REISSNER E. On the Problem of Stress Distribution in Wide-flanged Box-beams[J]. Journal of Aeronautical Sciences, 2015, 5(8):295-299.
[6] GONG Y M. Analysis on Space Stress of Block No.0 of Continuous Rigid Frame Bridge[J]. Journal of Highway and Transportation Research and Development, 2016, 33(6):83-87,94. (in Chinese)
[7] LI W H, HE S H, ZHAI X L, et al. Numerical Analysis and Optimal Design for Block on Pier Top of Long Span Beam Bridge[J]. Journal of Chang'an University:Natural Science Edition, 2011, 31(4):50-57. (in Chinese)
[8] WANG L F, WANG Z Q, ZHANG Y, et al. Stress Analysis of 0# Block in High Pier and Large Span Continuous Rigid Frame Bridge[J]. Journal of China & Foreign Highway, 2013, 33(2):177-179. (in Chinese)
[9] NING D B, QIANG S Z. Analysis on Space Stress of Block No. 0 in Beicha Bridge[J]. Engineering Mechanics, 2000, 17(A02):457-461. (in Chinese)
[10] DAI G L, SU M, LIU W S, et al. Stress Analysis of Pier-tower-girder Fixed Region of Cable-stayed Bridge with Trough Girder[J]. Journal of Hunan University:Natural Science Edition, 2014, 41(1):27-32. (in Chinese)
[11] REN W, LI W T, SONG Y F. Analysis Method of Numerical Model for Top Block of PC Box Girder Pier[J]. Journal of Highway and Transportation Research and Development, 2008(6):81-86. (in Chinese)
[12] WANG J, WU Q, XU W S, et al. Analysis of Spatial Stress of 0# Block in the Longest Cantilevered Stage of the Extradosed Cable-stayed Bridge[J]. Journal of Jiangsu University of Science and Technology:Natural Science Edition, 2016, 30(4):399-403. (in Chinese)
[13] ZHANG F, WANG Y, YAO L Y. Forward Analysis and Stage Deformation Control of Construction for Continuous Rigid Frame Bridge with V-shaped Pier[J]. Journal of Sanming University, 2018, 35(6):81-87. (in Chinese)
[14] RUAN J T, WANG S B, DING S R, et al. Numerical Analysis and Photoelastic Experiment for the Joint Structure in the Rigid Frame Bridge with Continuous Beam[J]. Journal of Experimental Mechanics, 2005(1):128-132. (in Chinese)
[15] PENG D C, YANG M G, MENG D L. Analysis on Stress of Pylon-pier-girder Rigid Region of Four-span Extradosed Cable-stayed Bridge with Three Pylons, Single Cable Plane and Long Flange[J]. Journal of Railway Science and Engineering, 2017, 14(7):1465-1472. (in Chinese)
[16] HE L, WANG J L. Method of Equivalent Load and Temperature Reduction on Prestressing Tendon for Effective Prestress Simulation[J]. Journal of Highway and Transportation Research and Development, 2015, 32(11):75-80. (in Chinese)
[17] JTG 3362-2018, Specifications for Design of Highway Reinforced Concrete and Prestressed Concrete Bridges and Culverts[S]. (in Chinese)
[18] NANNI A. North American Design Guidelines for Concrete Reinforcement and Strengthening Using FRP:Principles, Applications and Unresolved Issues[J]. Construction and Building Materials, 2003, 17(6):439-446.
2020, Vol. 14 
